A kitchen tap that drips once every few seconds can be more than an irritation when the house is quiet. Over time, that small leak wastes water, can mark the sink area with limescale and may point to a worn internal part that will only deteriorate. Many homeowners can fix a dripping kitchen tap with careful preparation and the correct replacement component, but knowing when to stop and call a professional matters just as much.
Start by identifying where the tap is leaking
Before taking anything apart, look closely at the source of the water. A drip from the end of the spout when both handles are off usually means the valve inside the tap is no longer closing fully. On a traditional tap, this is often caused by a worn rubber washer. On a modern monobloc mixer tap, a ceramic cartridge is more likely to be responsible.
Water around the base of the tap is a different issue. It may be caused by worn O-rings, a loose retaining nut or a seal that has failed around the tap body. A leak beneath the sink could come from the flexible tap tails, isolation valves or waste pipework rather than the tap itself. These faults need a more cautious approach, particularly where cupboards, electrics or flooring could be affected.
The age and type of tap will guide the repair. Separate hot and cold pillar taps commonly use washers, while quarter-turn and single-lever mixer taps usually contain ceramic cartridges. Replacing the wrong part can turn a straightforward job into several trips to the merchants, so take time to establish what you have first.
What you will need to fix a dripping kitchen tap
For a simple repair, gather an adjustable spanner, suitable screwdriver, small Allen key, cloth, plug or basin cover, and a replacement washer or cartridge that matches the tap. A little silicone grease can help when fitting seals, although petroleum-based grease should not be used on rubber components intended for drinking-water fittings.
It is worth placing the plug in the sink or covering the waste before you begin. Tiny screws, clips and seals have a habit of disappearing down the plughole at exactly the wrong moment. Lay a cloth over chrome surfaces before using a spanner too, as even a careful repair can leave unwanted scratches on a polished tap.
If your home has hard water, expect to find limescale around the components. This can make parts harder to remove, but force is rarely the answer. A seized tap body, rounded nut or cracked cartridge housing can quickly make a small repair more expensive.
Isolate the water supply first
Never dismantle a tap with the water supply still live. Look inside the kitchen cupboard for small isolation valves on the hot and cold pipework feeding the tap. They usually have a slotted screw that can be turned a quarter-turn with a flat-head screwdriver. The slot should sit across the pipe when the valve is closed.
Once isolated, open the tap to release the remaining water and check that the flow has stopped. If there are no local isolation valves, turn off the main stopcock. In some homes, the hot-water supply may need to be isolated separately depending on the boiler, cylinder or water-heating arrangement.
If an isolation valve will not turn, leaks when operated or appears badly corroded, do not force it. This is a sensible point to arrange a plumbing repair. A failed valve can leave you unable to restore the water supply safely once the work is complete.
Repairing a traditional washer tap
With a conventional pillar tap, the fixing screw is usually hidden beneath the handle cap. Carefully lift off the cap, remove the screw and pull the handle free. Underneath, you will find the tap headgear, which can be loosened with a spanner while holding the tap steady.
At the bottom of the headgear is a small rubber washer, normally retained by a screw or nut. If it looks flattened, split or hardened, replace it with an identical size. While it is apart, inspect the valve seat inside the tap body. A rough, pitted or damaged seat can prevent even a new washer from sealing properly.
Reassemble the tap without overtightening the components. Restore the water supply slowly, then test the tap. If it still drips, the seat may need re-facing or the headgear itself may be worn. Both jobs are best handled with the right tools and experience, particularly on older taps where replacement parts can be difficult to match.
Repairing a ceramic cartridge mixer tap
Most modern mixer taps use a ceramic cartridge rather than a washer. The handle may be held by a screw hidden beneath a decorative cap, behind a hot-and-cold indicator or underneath the lever. Once the handle is removed, a retaining collar or nut holds the cartridge in place.
Take a clear photograph before removing the cartridge, noting its orientation and any locating pins. Cartridges vary significantly in diameter, height, spline count and waterway arrangement. A cartridge that looks almost right may not fit, and an incorrect one can cause poor flow, temperature problems or continued leaking.
Lift out the old cartridge, clean away loose limescale and fit the new part in the same position. Check that any seals are seated correctly before tightening the retaining nut. Refit the handle, reopen the isolation valves gradually and test both hot and cold operation. A smooth lever movement and clean shut-off are good signs that the repair has worked.
When a dripping tap needs professional attention
A DIY repair is not always the most cost-effective option. Call a plumber if the leak is coming from pipework below the sink, if the tap has become loose on the worktop, or if the water cannot be isolated reliably. You should also seek help if there is damage to the tap body, persistent leaking after a new washer or cartridge, or signs of water damage inside the cupboard.
There is also a practical trade-off with older taps. If the finish is badly worn, the spout is stiff, replacement parts are unavailable or the tap has leaked more than once, fitting a new quality tap can offer better value than repeated repairs. The installation still needs to account for the existing sink, worktop, pipe connections and water pressure.
For households in Burgess Hill, Haywards Heath and nearby Sussex areas, a local plumbing engineer can identify the underlying cause, source compatible parts and make sure the repair is watertight rather than temporarily improved. This is particularly reassuring where a kitchen tap is part of a wider plumbing issue, such as poor pressure, leaking valves or ageing supply pipes.
Reduce the chance of another kitchen tap leak
Taps last longer when they are used gently. Avoid forcing handles shut, as excessive pressure can damage washers, cartridges and valve seats. Clean aerators and spouts regularly, especially in hard-water areas, because limescale can affect flow and encourage water to run back around moving parts.
If you notice a tap becoming stiff, noisy or slow to turn off, arrange attention before it starts dripping. Small changes in how a fitting feels often provide an early warning that seals or internal components are reaching the end of their serviceable life.
A properly repaired tap should turn off cleanly, stay dry around its base and give your kitchen back the quiet reliability it should have. Acting early protects more than water - it helps prevent a minor household nuisance becoming damage beneath the sink.